|
AVIATION MAINTENANCE TOOL
LIST* |
rev.08/06 |
|
|
|
|
The following is a list of the required hand tools you will
need for Aviation Maintenance |
|
|
(AER). You will be required to bring your tools
to
each laboratory period, unless advised |
|
otherwise by your instructor.
Storage of tools in the lab area will be at your own risk. |
|
|
If you do not have the tools required to perform the
practical
projects you will receive |
|
|
no
credit for the project. You may or
may
not be allowed to make up this project. |
|
|
|
|
|
|
| 1 |
Tool Box (No Rollaways) |
|
| 2 |
Padlock |
|
| 3 |
1/4
inch drive 12 Point Socket Set with at least the following sizes: 3/16", 7/32",1/4", |
|
|
9/32",5/16", 11/32", 3/8", 7/16", 1/2",
& 9/16", 1/4" universal joint and ratchet. |
|
| 4 |
3/8" drive 12Point Socket Set with at least the following sizes:
3/8", 7/16" 1/2", 9/16" |
|
|
5/8", 11/16" 3/4", 1/4", 5/16", 11/32",
13/16", 7/8", extensions 3" and 6" and ratchet. |
|
| 5 |
1/2 inch drive 7/8" Deep Socket 12 Point with a minimum 3"
Length |
|
| 6 |
3/8 inch to 1/2 inch adapter, 3/8" to 1/4" |
|
| 7 |
6 inch flexible steel ruler, 10ths, 100ths, 32nds, & 64ths |
|
| 8 |
8 foot Steel Tape |
|
| 9 |
4 inch common screwdriver |
|
| 10 |
8 inch common screwdriver |
|
| 11 |
1 1/2 inch (stubby) common screwdriver |
|
| 12 |
1 1/2 inch (stubby) # Phillips screwdriver |
|
| 13 |
6 inch #2 Phillips
screwdriver |
|
| 14 |
Combindation Wrench Set 1/4", 11/32", 3/8", 7/16",
1/2", 9/16", 5/8", 11/16", 3/4" |
|
|
13/16", and 7/8" |
|
| 15 |
6 inch duckbill pliers with serrations |
|
| 16 |
6 inch combination pliers |
|
| 17 |
6 inch longnose pliers |
|
| 18 |
6 inch diagonal cutters |
|
| 19 |
File Handle |
|
| 20 |
File Card |
|
| 21 |
10 inch flat fileSingle Smooth Cut |
|
| 22 |
10 inch flat fileDouble Bastard Cut |
|
| 23 |
10 inch 1/2 round file Single Smooth
Cut |
|
| 24 |
8 inch round file Single Smooth Cut |
|
| 25 |
3/16 inch center punch |
|
| 26 |
Pin Punch Set with at least the following sizes: 3/32",
1/8",
5/32", & 3/16" |
|
| 27 |
Combination Square |
|
| 28 |
Softface Mallet, approximately 2" in diameter |
|
| 29 |
Hacksaw frame |
|
| 30 |
18 teeth hacksaw blade - 4ea. |
|
| 31 |
32 teeth hacksaw blade - 4ea. |
|
| 32 |
8 ounce ballpeen hammer |
|
| 33 |
1 inch diamter round Inspection Mirror with extendable handle steel
back-NO PLASTIC |
|
| 34 |
2 inch round or rectangular
Inspection Mirror with extandable handle steel back-NO
PLASTIC |
| 35 |
1 Pair Mickey Mouse hearing protectors Min 130Db. |
|
| 36 |
1 Pair Safety glasses with clear lenses |
|
| 37 |
Magnifying glass with at least 10X power (ANY
SIZE) |
|
| 38 |
Dial Caliper calibrated in .001 - NO
PLASTIC |
|
| 39 |
D cell Flashlight with batteries -Flashlight must work -Non
Sparking |
|
| 40 |
10 inch wire brush |
|
| 41 |
5/64" thru 1/4 inch Allen Wrench Set |
|
| 42 |
24 test leads, #16 wire, 24 inches long with Alligator Clips |
|
| 43 |
14 thru 40 thread pitch gage. |
|
| 44 |
6 inch divider |
|
| 45 |
2
inch opening, light duty C-Clamps (3) |
Page 1 of 2 |
|
|
|
AVIATION MAINTENANCE TOOL LIST* (con.'t.) |
|
|
|
| 46 |
Pocket Knife |
|
| 47 |
Drill bits, #10, #21, #30, #40, 3/32", 1/8", 5/32"
(Need
at least 2 each #30 & #40) |
|
| 48 |
Digital Multi-Meter (VOM) with at
least 10amp DC (Check with Instructor before
Purchase) |
| 49 |
Fuses for the multi-meter |
|
| 50 |
Feeler Gauge with .0015"
thickness - .025 |
|
| 51 |
Cold Chisel 1/2" |
|
| 52 |
Mechanical fingers with minimum length 12". |
|
| 53 |
Fiber particle/Dust Mask (Purchase before Airframe II) |
|
| 54 |
The following is
needed for welding class: |
|
|
1 Pair monogoggle
Oxy-Acetylene cutting and welding goggles with shade #5 |
|
|
Friction
Lighter |
|
|
1 Pair Lightweight
Welder's Gloves |
|
|
Welders Cap |
|
|
1 Set Long Style Tip
Cleaners |
|
|
Soap Stone |
|
|
|
|
|
|
*This list is subject to change to meet department
requirements. |
|
|
*Tools requried for each course will be identified by
Instructor. |
|
|
*Tools not on this list must be approved by the instructor
before use. |
|
|
|
|
|
Page 2 of 2 |
